|
|
|
Look here for remaining stock and support information for our legacy products.
|
|
|
|
|
Digilent Adept
- Configures Xilinx logic devices, initializes scan chains, programs FPGAs, CPLDs, and PROMs, and organizes your configuration files
- Transfer data to and from the onboard FPGA on your system board. Read from and write to specified registers. Load a stream of data to a register or read a stream of data from a register.
- Organize and quickly connect to your communications modules.
- Can program Xilinx XCFS Platform Flash devices, Xilinx CoolRunner2 CPLDs, and most Xilinx Spartan and Virtex series FPGAs
Digilent Analog I/O 1
- converts from analog to digital and from digital to analog
- 2 dual op-amps
- multiple analog signal I/O connectors
- filters and amplifiers can be constructed for the data converters using the AIO1's solderless breadboard and op-amps
Basys FPGA Board, 250K gates
- Xilinx Spartan 3E FPGA, 250K gates
- Intended for use with ISE or Webpack
- Digilent USB2 port providing board power, programming, and data transfers
- VGA & PS/2 connectors
Cerebot
- Atmel ATmega64 with 64KB Flash, 4KB internal SRAM, 128KB external SRAM, 2KB EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable, Atmel AVR ISP, or Atmel JTAG ICE mk-II
- Connectors: Eight 6-pin Pmod, eight R/C servo, TWI daisy chain
Cerebot II
- Atmel ATmega64 with 64KB Flash, 4KB SRAM, 2KB EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable, Atmel AVR ISP, or Atmel JTAG ICE mk-II
- Connectors: Five 12-pin Pmod, three 6-pin Pmod, eight R/C servo, TWI daisy chain
Cerebot Plus
- Atmel ATmega2560 with 256KB Flash, 8KB internal SRAM, 128KB external SRAM, 4KB EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable, Atmel AVR ISP, or Atmel JTAG ICE mk-II
- Connectors: Ten 12-pin Pmod, one 6-pin Pmod, eight R/C servo, TWI daisy chain
Cerebot 32MX7
- Microchip® PIC32 32-bit MIPS processor (PIC32MX795F512L)
- Intended for use with MPLAB
- Program using MPLAB via onboard programming circuit
- Connectors: 6 x 12-pin Pmod™ headers, 2 x USB port, RJ45 Ethernet port, 2 x SPI ports, 2 x I2C ports
Ceres
- adjustable oscillator 0.5Hz-4KHz
- 4-digit, high-bright seven-segment display
- 4 debounce buttons and 8 slide switches
- 8 LEDs in red, green, and yellow
- 40 pin expansion connector capability
CY3240-I²C-USB Bridge Kit
- Populated with the CY8C24894 PSoC device
- Allows one to test, tune and debug hardware and software of a PSoC application by bridging the USB port to I2C
- Makes possible the connection of a wide variety of devices
Digilent 2
- dual on-board 1.5A power regulators (2.5V and 3.3 V)
- a socketed 50 MHz oscillator
- a 5-wire RS-232 serial port
- a status LED and pushbutton for basic I/O
- an EPP capable parallel port for JTAG-based FPGA programming and user data transfers
- six 100-mil spaced, right angle DIP socket 40-pin expansion connectors
Digilent 2E
- dual on-board 1.5A power regulators (2.5V and 3.3 V)
- a socketed 50 MHz oscillator
- a 5-wire RS-232 serial port
- a status LED and pushbutton for basic I/O
- an EPP capable parallel port for JTAG-based FPGA programming and user data transfers
- six 100-mil spaced, right angle DIP socket 40-pin expansion connectors
Digilent 2FT
- a JTAG programming port
- a status LED and pushbuttons for basic I/O
- an SMD 50MHz oscillator and a socket for a second oscillator
- dual on-board 1.5A power regulators (1.8V and 3.3 V)
- 172 I/Os routed to six standard 40-pin expansion connectors
- a socket for a JTAG-programmable 18V02 configuration Flash ROM
Digilent 2SB
- all 143 available user I/O's routed to six 40-pin expansion connectors
- a socket for a JTAG-programmable 18V02 Flash ROM
- dual on-board 1.5A power regulators (1.8V core and 3.3V I/O)
- a surface-mount 50MHz oscillator and a socket for a second oscillator
- a JTAG programming port and programming cable
- a status LED and pushbutton for basic I/O
Digilent 2XL
- dual on-board 1.5A power regulators (2.5V and 3.3V)
- a socketed 50MHz oscillator
- an SPROM socket for automatic FPGA configuration at power-on
- a status LED and pushbutton for basic I/O
- two 100-mil spaced, right-angle DIP socket 40-pin expansion connectors
- an EPP-capable parallel port for JTAG-based FPGA programming and user data transfers
Digital Breadboard 1
- Large 540 tie-point breadboard with separate pre-connected power/GND tracks
- Test point connections on every signal
- Compatible with any system board using 2x20 pin header connectors
- Prototype connections on every signal
Digital I/O 1
- a four digit seven-segment LED display
- 8 individual LEDs
- a 3-bit VGA port
- 5 momentary pushbuttons
- 8 slide switches, and a PS2 mouse/keyboard port
Digital I/O 2
- a 16x2 character LCD with integral Samsung controller IC
- a four digit seven-segment LED display, and 16 individual LEDs of various colors
- an 8-bit VGA port, and a 15-button keypad
- 8 slide switches, and a PS2 mouse/keyboard port
- an on board 5VDC regulator
Digital I/O 4
- four-digit seven-segment display
- 8 LEDs and 8 slide switches
- 4 debounced pushbuttons
- a 3-bit VGA Port
- a PS/2 mouse or keyboard Port
Digital I/O 5
- a 16x2 character LCD module
- a 4-digit seven segment LED display
- 16 LEDs in three different colors, and a 16 button keypad
- 8 slide switches, and a 3-bit VGA port
- a PS/2 mouse or keyboard port
DM240011
MPLAB Starter Kit for PIC24F
- Contains everything needed to experience the high performance and versatility of the PIC24F microcontroller family.
DM163029
PICDEM™ Mechatronics Demonstration Kit
- The PICDEM Mechatronics demonstration board is an easy-to-use development and demonstration platform for implementing intelligent control in a mechanical system.
DM320001
PIC32 Starter Kit
- The PIC32 Starter Kit contains everything needed to experience the high performance PIC32 microcontroller family.
DM300024
dsPICDEM 1.1 Plus Demo Board
- Provides the application designer with a low cost development tool to become familiar with the dsPIC30F/33F and PIC24H 16-bit architecture, high performance peripherals and a powerful instruction set.
Digilent XCRP
- non-volatility - designs remain in the CPLD after power is removed
- on-board voltage regulator for use with a wall-plug transformer, or the board can run more than 60hrs on 2 AA cells (typical)
- expandability -an integral solderless breadboard allows expansion circuits to be constructed right on the XCRP board
- four debounced buttons, eight slide switches, eight LEDs in red, green, and yellow, a 40-pin expansion connector, and two high-bright seven segment displays
- a user-adjustable oscillator circuit (approximately 0.5Hz to 4KHz)
SMSC EVB-USB3300-XLX USB Daughter Card
- SMSC USB3300 USB Transciever
- USB-IF "Hi-Speed" Certified
- Supports 480 Mbps High Speed (HS) and 12 Mbps Full Speed (FS) and 1.5 Mbps Low Speed (LS) Serial Data Transmission Rates
- Includes Probe Points on All Data and Control Signals for Troubleshooting
FX12 Board
- Virtex-4 FX12 FPGA
- JTAG programming port that can accommodate all Digilent and Xilinx programming cables
- XCF08 Xilinx Platform Flash ROM to store FPGA configurations
- Marvell 88E1111 "Alaska" Gigabit Ethernet PHY
- 24-bit Analog Devices high-speed video DAC
- 64 MB of ISSI DDR SDRAM
- 16 MB of Micron Flash ROM
- Linear Technology high-current switching power supplies
- Linear Technology FASTDAACS connector for driving high speed analog peripherals
- User-settable Integrated Circuit system frequency synthesizer (up to 300+ MHz)
- On-board RS-232 serial port, LCD display, buttons, switches, and LEDs
- High-speed capable Hirose expansion connector
JTAG-USB Full Speed Module
- Improved low-cost JTAG configuration & SPI communication solution
- Connects to a standard 6-pin JTAG or SPI programming header
- Can be used with Digilent Adept & AVR Device Programmer software
- Can program devices that have a JTAG voltage of 1.8V or greater
- Requires Adept 2.0 or later for operation
Contact us
for pricing & availability
MDE 8051 Trainer
- Maxim DS89C4XX with 1K SRAM, 16K-64K Flash
- Intended for use with any standard 8051 development tools
- Programmable via serial cable (included)
- Connectors: Two full-duplex serial ports, male & female headers for all ports
MDE PIC18 / PIC16 Trainer
- Microchip® PIC18F & PIC16F (both included)
- Intended for use with MPLAB
- Programmable via PICkit™ 2 (can be added to kit)
- Connectors: One serial port, male & female headers for all ports
Memory Module 1
- static RAM memory
- flash ROM memory
- provides memory for use in logic designs
Module Interface Board
- eight 6-pin headers for connection to module boards
- separate power selection for each 6-pin header
- a 40-pin header and a 40-pin socket
- flexible power routing
Minicon
- Atmel ATmega168 with 16KB Flash, 1KB SRAM, 512B EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable or Atmel AVR Dragon
- Connectors: Five 6-pin Pmod, TWI daisy chain
Nanocon
- Atmel ATmega168 with 16KB Flash, 1KB SRAM, 512B EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable or Atmel AVR Dragon
- Connectors: Four 6-pin Pmod, TWI daisy chain
Network 1
- 10Mbit Ethernet port
- can be used to program system boards
- can be used to transfer data between a PC and a system board
- media access controller
Nexys
- Xilinx Spartan-3 FPGA (400K gates)
- Intended for use with ISE or Webpack
- Digilent USB2 port providing board power, programming, and data transfers
- 16MB Micron CellularRAM, 4MB Numonyx StrataFlash, high-speed expansion connector
Nexys Graphic LCD Module
- Digitron SG12864I Graphic LCD
- 128x64 pixel dot-matrix graphic LCD
- Displays both Text and Graphics
Nexys LCD Module
- 16x2 character LCD
- Samsung KS0066 compatible controller
Nexys VGA Module
- VGA module with 16-pin header for use with the Nexys Board
- 12 bit video output
- Produce up to 4,096 colors on a standard VGA monitor
Digilent Pegasus
- Three expansion connectors for peripheral boards
- four-digit seven-segment displayand 8 LEDs
- 8 Slide switches and 4 pushbuttons
- VGA and PS2 ports
- ships with programming cable and power supply
Parallel I/O 1
- DB25 female parallel port allows use of inexpensive, straight-through parallel cables
- can be used for SPP and EPP mode data transfers
- compatible with all Digilent system boards
- an EPP-compatible parallel port for use with Digilent system boards
- allows bi-directional user data transfers between a PC and a Digilent system board
PmodAMP1 - Speaker / headphone amplifier
- 6-pin header for inputs
- 3V-5V operating voltage
- Small size (0.80" x 1.15")
- Ships with a 6" 6-pin cable and a 6-pin header
PmodBT - Bluetooth Interface
- Provides Bluetooth support in either a transparent serial cable replacement mode or a more powerful command mode
- Wide range of profiles including generic access profile, service discovery profile, and the serial port profile
- Simple UART interface
- 2.5V – 3.6V operating voltage
- Small size (.8" x 1.5")
- Ships with a 6" 12-pin cable, a 6" 2x6-pin to dual 6-pin cable, one 12-pin header, and two 6-pin headers
PmodCON2 - BNC connectors
- Two signal routing jumper blocks
- Small size (2.06" x 1.44")
- Ships with a 6" 6-pin cable and a 6-pin header
Digilent H-Bridge 2 board
- Dual 1A H-bridges
- 4.5V to 12V supply voltage
- Screw terminal connectors for power supply and motors
- Logic level inputs
PmodNIC - Network Interface Controller
- 10 Mb/s IEEE 802.3 compatible Ethernet controller
- SPI interface
- 10BASE-T MAC/PHY
- Small size (1.65" x 0.80")
- Ships with a 6" 12-pin cable, a 6" 2x6-pin to dual 6-pin cable, one 12-pin header, and two 6-pin headers
PmodRF1 - Wireless Radio Transciever
- NOTE: This product has been replaced by the PmodRF2.
- Operates in selected frequency ranges within the North American ISM band, the European SRD band, and the Chinese WPAN band
- Features a standard SMA connector for use with a wide range of antennas (2" antenna included)
- Small size (1.5" x 0.75")
- Ships with a 6" 12-pin cable, a 6" 2x6-pin to dual 6-pin cable, one 12-pin header, and two 6-pin headers
PmodTMP - Thermometer/thermostat
- Maxim DS1626 high precision three wire thermometer/thermostat
- 6-pin header and 6-pin socket
- Requires no external components
- Temperature range from -55C to +125C
- Ships with a 6" 6-pin cable and a 6-pin header
Robotic Development Kit - Basic
- Complete kit with all the parts & software necessary to build and program an autonomous robot
- Complete manual & reference design walk you through every step to get things up & running
- Includes:
- Our RSK robotic platform (w/ extra endplate extension)
- A Cerebot™ MX4cK microcontroller board
- PmodCLS 2-line character LCD display
- PmodBTN and PmodSWT modules for I/O
Robotic Development Kit - Line Sensor
(DC motor-driven)
- Complete kit with all the parts & software necessary to build and program a line-follower robot
- Complete manual & reference design walk you through every step to get things up & running
- Includes:
- Our RSK robotic platform (w/ sensor mounting bracket)
- A Cerebot™ MX4cK microcontroller board
- PmodLS1 infrared detector module
- Four infrared sensors
Robotic Development Kit - Line Sensor 2
(servo-driven)
- Complete kit with all the parts & software necessary to build and program a line-follower robot
- Kit contains everything you need to get up & running
- Includes:
- Our RSK robotic platform modified for use with servo motors & a sensor mounting bracket
- A Cerebot MX3cK microcontroller board
- PmodCON3 servo interface module
- PmodLS1 infrared detector module
- Four infrared sensors
Robotic Development Kit - Remote Control
- Complete kit with all the parts & software necessary to build and program a wired remote control robot.
- Complete manual & reference design walk you through every step to get things up & running
- Includes:
- Our RSK robotic platform (w/ sensor mounting bracket)
- A Cerebot™ 32MX4 microcontroller board
- PmodJSTK joystick module
- PmodRJ45 (pair)
- Ethernet cable
R2R Module
- 8-bit digital to analog conversion at up to 25MHz +
- easy attachment of oscilloscopes to illustrate the data conversion process
- inexpensive and rugged construction
- R-2R resistor divider network that can convert an 8-bit digital input signal to an analog value
Robotic Starter Kit
- Rugged metal platform with mounting holes on 1/2" centers
- Two 1/19 ratio motor/gearbox drives with ABS plastic wheels (1/53 gear ratio option available)
- Two Digilent PMOD HB5, 2A H-bridge motor amplifiers with attachment clips
- Rugged plastic wheels and drag button
- Rugged metal motor mount
- AA Battery Holder (holds four AA batteries)
- All wiring and assembly hardware included
SASEBO-GⅡ-32 Side-channel Attack Standard Evaluation Board
- Designed for the purpose of side-channel cryptographic attack experiments
- Features two FPGAs:
- Cryptographic FPGA: Xilinx Virtex-5 LX50
- Control FPGA: Xilinx Spartan-3A 400
- Both FPGAs are connected through a 38-bit common I/O bus with full flexibility in signal assignment
- Shunt resistors are provided to insert on the core VDD and/or ground lines of the cryptographic FPGA for measuring power traces
- USB interface for power supply & configuration
- NOTE: You must submit an Export Compliance Certificate before we can process your order. Click on "More Info" for details.
Solderless Breadboard Kit - Small
- Convenient breadboard for constructing small-to-medium circuits
- Self-adhesive backing - can be affixed to any surface
- 1x 630 tie point terminal strip
- 1x 100 tie point distribution strip
- 1.75 x 4.5 inches
ServoMini
- Atmel ATmega168 with 16KB Flash, 1KB SRAM, 512B EEPROM
- Intended for use with Atmel AVR Studio & WinAVR
- Programmable via Digilent JTAG USB cable or Atmel AVR Dragon
- Connectors: Eight R/C servo, TWI daisy chain, One 6-pin Pmod
USB 2 Module
- USB 2.0 connector
- status indicator LED
- Cypress CY7C68013 USB controller
- small form factor (3.00" x 2.20")
Video Decoder board
- Decode NTSC/PAL/SECAM video sources
- Composite, component, and S-Video inputs
- Ideal for video & image processing experiments
Voltage Regulator Module
- 6A synchronous step down switcher
- Selectable 5V or 3.3V output voltage
- Input voltage range of 5-15V
- 479kHz internal switching frequency
- Switching synchronization to an external clock
X-Board
- Xilinx CoolRunner-II CPLD (256 Macrocells)
- Intended for use with ISE or Webpack
- Programmable via Digilent parallel or USB JTAG cable
- Eight 6-pin Pmod connectors, On-board current monitor
Digilent XC2XL
- Xilinx CoolRunner II CPLD (256 Macrocells) & XC9500 CPLD (72 Macrocells)
- a socketed oscillator (1.8432MHz included; clocks up to 100+MHz can be used)
- full routing of all I/O signals from both CPLDs to expansion connectors
|
|
